Foam Foam Foam your Boat

After laying new carbon fiber cloth on both interior sides of the bow, which stiffened the hull and gave it integrity again, it was time to follow through with setting the blue XPS foam. I had tried cutting the foam with a razor knife, a hand saw and even a kitchen knife. Of those three the kitchen knife was easiest to work with to get a clean cut. However, I spent $20 on a hot foam cutter through Amazon and got my best results. None of those little blue styrofoam balls and relatively easy to cut complex curves. You definitely want to wear a respirator. The fumes are nasty.

All in all, I figure I added about 2 ounces of foam to the weight. I left a little gap on other side to ensure I was not spreading the hull and ensure the top would fit.

Hot Foam Cutter
Dry Fitting Foam

Foam Inset by Repaired Crack



Phase 1 of Returning the Top Nose

Since I also needed to repair cracks in the hull under the seat, it was decided to simply add a deck plate with access cover instead of returning the carbon patch. The deck plate cost $15 from West Marine and the hatch will be utilized to attach a small storage bag. The plate is made from ABS plastic, heavier and stiffer than carbon, so I think it will actually stiffen the area of the hole, though it added a few ounces as well.

Since I've lost 4 pounds, we're in good shape!

Stay tuned as we prepare for the Swimming Pool Test.

TO BE CONTINUED

Comments

  1. adarachristJanuary 5, 2018 at 10:04 PM

    Oh, that is really bad that you have spent much still you have not got the desired result. Boat decking foam is an essential for boat. I hope you come out of this as soon as possible.

    ReplyDelete

Post a Comment

Popular posts from this blog

The Hole, Hull and Huli Truth - Testing Carbon Fiber Repairs

Image
I did a very lazy huli (boat flip) on the Hudson River without thinking through that I had cut an 8" hole in the Puakea Kaku just behind the seat. This was patched in with a deck plate and white silicone. It wasn't until I had righted the craft and paddled back to shore that I realized I should have not only checked the canoe for leaks when it was right side up in the pool but also when it was upside down. About twenty years ago I caulked a 26 story hotel as an apprentice, so I guess you can say it paid off! Picture Perfect Portal into the Carbon Hull  It was time to epoxy the top of the bow back into place. There was concern it might not quite fit the same way, and there did prove to be a minor snarl in the top where the major puncture had contracted during repair. Nothing some fairing compound couldn't cover up later. Black epoxy used to join carbon seams  It is critical to mate the seams and not get too ambitious with laying carbon on the exterior. If anyth
Read more

Puakea OC1 Rescue

Image
What kind of OC1 costs $175? Well, who knows? But that was the price tag the night I randomly googled for used outrigger canoes. 1: usually the hits are scarce. 2: usually the listings are for OC's almost as expensive as new. 3: usually these OC's are in California or Hawaii. They are never in Lousiana and certainly not on a Louisiana Air Force Base. But there it was, $175 on eBay. It was listed as a fixer upper missing a rudder. Well, since I've thrown away a couple hundred dollar bills on much more foolish things, I gambled and bought it. The seller was kind enough to wrap it in its case and bubble wrap the ama and i'aku's as well as the seat. Federal Express was dumb enough to lose the X-shaped PVC cradles it was sitting on. The Fedex guys who carried it out marveled at how light it was, but I was concerned that the boat had parted ways with the cradles and been rolling around in transit  There is no way to insure a used craft like this, so it was all par
Read more

3D Print Pedals for Outrigger Canoe - Puakea Kaku

Image
 Tonight I finally got to install the new 3D printed pedals. I work with SketchUp and exported the file to STL. From there I went to 3D Print Hubs and chose a hub in Connecticut. I went back and forth with the owner of Diversified Manufacturing Tech while I refined the basic design. He suggested the carbon fiber/nylon material named "onyx." I spent considerable time engineering the holes through which the bungee cord and rudder lines would connect, and during attachment I had a friend hold the rudder while I toyed around with the length of the lines, seeking the right amount of tension. 3D printed ONYX pedals, $20.80 total Not only are the pedals great, Andrew even did a follow up. A lot of customer service for $20.80, and he threw in a tablet stylus as a business promo gift. As someone who owns three tablets, I really appreciate that. So, here is his plug: Diversified Manufacturing Technologies website . My first SketchUp drawing based on the old pedals Not
Read more